1 GAL Armor WB15 Low Gloss Water Based Acrylic Concrete Sealer

Rating:
80% of 100

The Armor WB15 is a low gloss water based acrylic cure and seal that meets or exceeds ASTM 1315 and ASTM C 309 standards. When properly applied, the Armor WB15 will help concrete to properly cure by reducing premature moisture loss. It will also help to reduce deterioration caused by surface abrasion, foot traffic, and spills.

While the Armor WB15 is approved as a cure and seal, it can also be applied to existing concrete and paver surfaces to achieve a long lasting, UV resistant, breathable low gloss finish.

$64.99
Availability: In stock
SKU
WB151GAL

The Armor WB15 is a water-based acrylic sealer designed to seal and protect concrete and paver surfaces with a durable low gloss surface film. The Armor WB15 is a fantastic sealer if you are looking to enhance surfaces with a low gloss finish.

The Armor WB15 is made from high quality, non-recycled, US manufactured resins. It is non-yellowing, breathable, and low VOC. The protective low gloss film will reduce damage and deterioration caused by surface abrasion and water absorption including cracking, spalling, pitting, dusting, and the growth of mold, mildew, and algae.

Benefits:

  • Protective surface film will reduce damage and deterioration caused by water absorption and surface abrasion
  • Protective surface film will reduce the growth of mold, mildew, and algae on the surface
  • Made from non-recycled US manufactured resins
  • Easy to apply, easy to maintain, easy to re-coat
  • UV resistant, breathable

Uses:

The Armor WB15 is a great choice for a variety of interior and exterior concrete applications, including:

  • Pool decks and patios
  • Driveways, walkways, and stairs
  • Garage and basement floors
  • Retail and shop floors
  • Warehouse floors
  • Much more!

The WB15 can be applied to a variety of interior and exterior concrete surfaces, including:

  • Stamped concrete
  • Poured and broom finished concrete
  • Exposed aggregate concrete
  • Concrete pavers
  • New, uncured concrete

The Armor WB15 is designed specifically to be used on unsealed concrete and concrete pavers. It can also be applied to concrete and concrete paver surfaces previously sealed with a water based acrylic as long as the acrylic has been properly prepped for adhesion. The Armor WB15 should not be used to seal clay brick, red Chicago pavers, flagstone, slate, or natural stone. If you are looking to seal clay brick, red Chicago pavers, flagstone, slate, or natural stone, consider instead of the Armor WL550 or the Armor SX5000 WB.

The Armor WB15 can’t be applied over any other film forming sealer, other than a water-based acrylic sealer. It can’t be applied over a water based acrylic, an acrylic latex, a paint, epoxy, or urethane.

Appearance

When applied in clear, the Armor WB15 will provide a transparent low gloss finish.

The actual level of gloss and enhancement received will depend on the type and age of the surface, age, porosity, condition, applicator, application method, and amount of material applied. For an accurate representation of what your surface will look like once sealed, we suggest applying the product to a test area first.

Product Life

When properly applied, the Armor WB15 can provide up to 1-3 years of life on an exterior surface before the need to recoat, and up to 2-7 years of life on an interior surface.

While the Armor WB15 is designed to out-last and out-perform similar products on the market, there are several factors that can impact actual product life including the severity of surface abrasion and level of foot traffic, the porosity of the concrete or pavers, and the amount of resin build-up on the surface. Some surfaces need to be sealed every year, while others can go a few years without sealing.

The Armor WB15 can be applied with a 3/8-1/2” nap roller, or an HVLP sprayer. For a consistent low gloss finish, apply two coats spaced 6-8 hours apart. Do not exceed 24 hours apart between coats.

Time Of Day

The Armor WB15 should only be applied in the early evening (around 5 PM or later) when air and surface temperatures are declining, and when the sun is no longer positioned over the surface.

Surface Preparation

The Armor WB15 should be applied to a completely clean and dry surface. If the surface was cleaned with water or pressure washed prior to application, allow the surface to dry for at least 24 hours before sealing. While the surface may appear dry and feel dry to touch, water below the surface trapped in the pores can cause the same issues. While pressure washing the surface is typically sufficient, spot treatment may be necessary for deep or older stains.

The Armor WB15 is designed specifically for use on unsealed concrete and concrete paver surfaces, as well as concrete and concrete pavers previously sealed with a water based acrylic. Do not apply this product over a surface previously sealed with a solvent based acrylic, or any other type of film-forming sealer.  If the surface is smooth troweled, or does not easily accept water, acid etching may be required prior to applying sealer. It is always suggested to apply the Armor WB15 to a test area to verify absorption, coverage, compatibility, and project suitability.

Note About Sealing Pavers:

Please note, the Armor WB15 is not a bonding agent. Do not apply the Armor WB15 over loose sand between paver joints because it will not harden or seal the loose sand. The Armor WB15 can be applied over the pavers directly, or the pavers and polymeric sand (if the polymeric sand is newly installed, wait 7 days before sealing), but it can’t and should not be applied over loose sand.

Adding Non-Slip: For best results, apply the Armor non-slip additive with an appropriate hand-held broadcast spreader. When applying the second coat, add the non-slip additive to the coating using a broadcast spreader, and back roll to encapsulate the non-slip additive.

 

For complete application instructions and safety data, please refer to the Documents tab.

Porous Surfaces: Up to 175 FT2/gallon in one coat.

Smooth Surfaces (once properly prepped): Up to 200-225 FT2/gallon in one coat.

Coverage will vary depending on porosity, surface condition, application method, and the amount of material applied by the applicator. The above coverage rates are estimates and will vary. Two coats are suggested for even coverage and appearance.

 

Write Your Own Review
You're reviewing:1 GAL Armor WB15 Low Gloss Water Based Acrylic Concrete Sealer
Your Rating