Free Shipping on All Orders
The Armor SX5000 WB is a Department of Transportation approved water based Silane-Siloxane water repellent sealer for unsealed concrete, brick, stone and masonry.
$15.00 – $224.99
The Armor SX5000 WB is a Department of Transportation approved water based Silane-Siloxane water repellent sealer for unsealed concrete, brick, stone and masonry.
$15.00 – $224.99
Up To 175-225 ft2/gallon
Up To 7-10 Years
Natural
Water Based Silane Siloxane
The Armor SX5000 WB is a Department of Transportation approved water based Silane-Siloxane water repellent sealer for unsealed concrete, brick, stone and masonry.
Surface Preparation:
The Armor SX5000 WB should be applied to a completely clean and dry surface. If the surface was cleaned with water or pressure washed prior to application, allow the surface to dry for at least 24 hours before sealing. While the surface may appear dry and feel dry to touch, water below the surface trapped in the pores can cause the same issues. While pressure washing the surface is typically sufficient, spot treatment may be necessary for deep or older stains. If the surface is smooth troweled, or does not easily accept water, acid etching may be required prior to applying sealer. It is always suggested to apply the Armor SX5000 WB to a test area to verify absorption, coverage, compatibility, and project suitability.
The Armor SX5000 WB is designed specifically for unsealed concrete and masonry surfaces. Do not apply this product over a surface recently sealed with a water repellent sealer, or previously sealed with a film-forming sealer or coating.
Application:
A commercial pump sprayer is recommended to achieve the best coverage and results. Be sure the psi is no greater than 20. Use a .3-.5 GPM adjustable cone tip.
Apply the first coat of Armor SX5000 WB, ensuring the entire surface is evenly saturated. Wait at least 10-15 minutes, then apply the second coat. Do not flood the surface or allow puddles to form, this will result in over application and the formation of dark spots on the surface. Less porous surfaces, such as bluestone, flagstone, and slate, may only require one coat.
Substrates sealed with Armor SX5000 WB may be coated with silicone emulsion paints and many oil based paints once the surface has had 72 hours to dry. Testing is always necessary and recommended to assure proper adhesion. Adhesion may be improved if the surface is pressure washed and allowed to dry prior to application. Armor SX5000 WB is not a paint primer. Adhesion of cementitious coatings, stucco, plaster, etc., may be adversely affected. These types of substrate treatments should be installed and allowed to fully cure before applying Armor SX5000 WB. Always test to verify compatibility.
Time of Day
The temperature of the air and surface must be 55-85 degrees F during application. If freezing conditions exist prior to application, it is highly recommended that the substrate be allowed to fully thaw. Should this recommendation not be followed, the product may not yield adequate protective properties.
Once applied, the surface should be kept dry for at least 24 hours.
Clean-Up
Use warm water and soap. Dispose of containers in accordance with local and federal regulations.
Product Removal
Armor SX5000 WB penetrates deep into to the surface. Removal is not recommended.
Porous Surfaces: Up to 175 FT2/gallon in one coat.
Smooth Surfaces (once properly prepped): Up to 200-225 FT2/gallon in one coat.
Coverage will vary depending on porosity, surface condition, application method, and the amount of material applied by the applicator. The above coverage rates are estimates and will vary. Two coats are suggested for even coverage and appearance. Please note, less porous surfaces, such as bluestone, flagstone, and slate may only require one coat.
The Armor SX5000 WB is designed specifically to be used on unsealed concrete, brick, natural stone, and masonry. The Armor SX5000 WB can’t be applied over any existing sealers, paints, or coatings.
The Armor SX5000 WB is a fantastic sealer for a variety of applications, including:
The Armor SX5000 WB is designed to work entirely below the surface. It chemically reacts to form a hydrophobic barrier in the pores. It will not change the look or color of the substrate, and it will not leave a visible surface film.
If you are looking for a wet look, low gloss, or high gloss, consider instead the Armor WL550 for a matte wet look, the Armor AR350 for a low gloss wet look, or the Armor AR500 for a high gloss wet look.
When properly applied, the Armor SX5000 WB can provide up to 7-10 years of life on an exterior surface before the need to recoat.
Water Bead: Surface water beading will not occur on all surfaces. While some surfaces may experience an instantaneous bead, others won’t experience a surface water bead at all. Surface water beading is not a sealer benefit. Surface water bead is caused from resin build-up on the surface. Once the resin build-up goes away, so will the bead. The Armor SX5000 WB is designed to work entirely below the surface so its benefits are made visible through performance. You will find sealed surfaces dry faster, are easier to clean, and experience less damage caused by freeze-thaw cycles and de-icing salts.
Free Shipping: Orders placed before 4 PM EST are shipped same day. Orders placed on the weekend, or on holidays, will be shipped the next business day. Once your order ships you will receive an email with tracking information. For any questions, please don’t hesitate to contact a member of our Customer Support staff.
Free Returns: Returns are accepted on unopened and unused product within 30 days from the date the product was received. If you need to make a return, please contact us for a pre-paid return label. We can be reached at 866-306-0246, or via email at [email protected].
T (866) 306-0246
Foundation Armor
3 Howe Drive, Suite 2, Amherst, NH 03031
CAGE Code: 77PK6
DUNS: 078654562
Primary NAICS: 325510
Women Owned Business Certified (WBENC)
DOT DBE Certified