Free Shipping on All Orders
The Armor AR500 is a solvent-based pure acrylic sealer designed to enhance and protect concrete and concrete pavers with a high gloss wet look.
$15.00 – $224.99
The Armor AR500 is a solvent-based pure acrylic sealer designed to enhance and protect concrete and concrete pavers with a high gloss wet look.
$15.00 – $224.99
Foundation Armor color packs for solvent based acrylic sealers are a great way to enhance your existing concrete and concrete pavers with a color. For an opaque, paint-like finish you can mix in the Armor Opaque Color Packs, and for a semi-transparent brown or gray finish you can mix in the Armor Semi-Transparent Color Packs.
Up To 175-225 ft2/gallon
Up To 1-3 Years
High Gloss Wet Look
Solvent Based Pure Acrylic
The Armor AR500 is a solvent based pure acrylic sealer designed to enhance and protect concrete and concrete pavers with a high gloss wet look.
The Armor AR500 can be applied with a 3/8-1/2” nap roller, or a solvent resistant commercial pump sprayer. For a consistent wet look and high gloss finish, apply two coats spaced 24 hours apart.
Time Of Day
The Armor AR500 should only be applied in the early evening when air and surface temperatures are declining, and when the sun is no longer positioned over the surface. To avoid bubbling and hazing, do not apply in the morning or middle of the day.
Surface Preparation
The Armor AR500 should be applied to a completely clean and dry surface. If the surface was cleaned with water or pressure washed prior to application, allow the surface to dry for at least 24 hours before sealing. While pressure washing the surface is typically sufficient, spot treatment may be necessary for deep or older stains.
The Armor AR500 is designed specifically for use on unsealed concrete and concrete paver surfaces, as well as concrete and concrete pavers previously sealed with a solvent based acrylic. If the concrete is smooth or trowel finished, and doesn’t quickly and easily absorb water, other surface preparation may be required to open up the surface pores, such as acid etching or grinding. If applying over a surface with a water based acrylic, or old, degrading solvent based acrylic, remove the current coating with the Armor CR100 prior to applying the Armor AR500.
The Armor AR500 should not be used to seal clay brick, red Chicago pavers, flagstone, slate, or natural stone. If you are looking to seal clay brick, red Chicago pavers, flagstone, slate, or natural stone, consider instead of the Armor WL550 or the Armor SX5000 WB.
Note About Sealing Pavers:
Please note, while the Armor AR500 can be applied over paver joints, it is not designed as a bonding agent and will not harden or bond the loose sand in the paver joints. If applying with a roller, loose sand in the joints may cling to the roller and be redistributed across the pavers. For best results, apply first coat with a sprayer if you are applying to pavers with loose sand in the paver joints.
When applying to porous pavers, gloss level may be reduced, and more material may be required to achieve desired finish.
Mixing Opaque Color Packs: Do not exceed more than 6 ounces of color per gallon of sealer. Stir color well before adding to sealer, then once added to sealer, stir again, ensuring color is evenly mixed. Once cured, will cover like a paint—you will be left with an opaque colored finish.
Mixing Semi-Transparent Color Packs: Do not exceed more than 1 ounce of color per gallon of sealer. Stir color well before adding to sealer, then once added to sealer, stir again, ensuring color is evenly mixed. Once cured, will offer a semi-transparent tinted finish.
Adding Non-Slip: For added surface traction, the Armor Non-Slip additive can be added. The ultra-fine, fine, and coarse Armor Non-Slip additives works best in the Armor AR500. Applying the Ultra-Fine: Slowly drill mix 3-6.5 ounces of non-slip additive per gallon of sealer, until completely blended, then apply. For Fine and Coarse: When applying the second coat, add the non-slip additive to the coating using a broadcast spreader, and back roll to encapsulate the non-slip additive.
Clean-Up
Use Xylene or acetone. Dispose of containers in accordance with local and federal regulations.
Product Removal
Dried, cured sealer may be removed with a the Armor CR100, or by using a diamond grinding method, sandblasting method or similar mechanical action.
Porous Surfaces: Up to 175 FT2/gallon in one coat.
Smooth Surfaces (once properly prepped): Up to 200-225 FT2/gallon in one coat.
Coverage will vary depending on porosity, surface condition, application method, and the amount of material applied by the applicator. The above coverage rates are estimates and will vary. Two coats are suggested for even coverage and appearance.
The Armor AR500 is a great choice for a variety of interior and exterior concrete applications, including:
The AR500 can be applied to a variety of interior and exterior concrete surfaces, including:
The Armor AR500 is designed specifically to be used on unsealed concrete and concrete pavers. It can also be applied to concrete and concrete paver surfaces previously sealed with a solvent based acrylic. The Armor AR500 should not be used to seal clay brick, red Chicago pavers, flagstone, slate, or natural stone. If you are looking to seal clay brick, red Chicago pavers, flagstone, slate, or natural stone, consider instead of the Armor WL550 or the Armor SX5000 WB.
The Armor AR500 can’t be applied over any other film forming sealer, other than a solvent-based acrylic sealer. It can’t be applied over a water based acrylic, an acrylic latex, a paint, epoxy, or urethane.
The Armor AR500 ships in clear and offers a high gloss finish. Armor Opaque Acrylic Color Packs can be added for a tinted opaque high gloss finish, and Armor Semi-Transparent Acrylic Color Packs can be added for a tinted semi-transparent high gloss finish.
The actual level of gloss and enhancement received will depend on the type and age of the surface, age, porosity, condition, applicator, application method, and amount of material applied. For an accurate representation of what your surface will look like once sealed, we suggest applying the product to a test area first.
When properly applied, the Armor AR500 can provide up to 1-3 years of life on an exterior surface before the need to recoat, and up to 2-7 years of life on an interior surface.
While the Armor AR500 is designed to out-last and out-perform similar products on the market, there are several factors that can impact actual product life including the severity of surface abrasion and level of foot traffic, the porosity of the concrete or pavers, and the amount of resin build-up on the surface. Some surfaces need to be sealed every year, while others can go a few years without sealing.
Free Shipping: Orders placed before 4 PM EST are shipped same day. Orders placed on the weekend, or on holidays, will be shipped the next business day. Once your order ships you will receive an email with tracking information. For any questions, please don’t hesitate to contact a member of our Customer Support staff.
Free Returns: Returns are accepted on unopened and unused product within 30 days from the date the product was received. If you need to make a return, please contact us for a pre-paid return label. We can be reached at 866-306-0246, or via email at [email protected].
T (866) 306-0246
Foundation Armor
3 Howe Drive, Suite 2, Amherst, NH 03031
CAGE Code: 77PK6
DUNS: 078654562
Primary NAICS: 325510
Women Owned Business Certified (WBENC)
DOT DBE Certified